Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Venice, CA
Gate access control and gate parts work in Venice, CA has to account for one thing before anything else: salt air. Properties here sit on the Pacific, and the marine layer keeps metal damp for months at a time. That changes which keypads survive, which hinges hold, and how fast an opener’s circuit board corrodes. We quote and perform both services here with a written price handed over before any work starts. Call (424) 373-8425 if you need a gate looked at.
Why Venice Homes Are Different
Venice’s housing stock is a patchwork. The Abbot Kinney-era bungalows from the 1910s and 1920s sit on narrow lots with tight single-car driveway entries, often with original wrought-iron swing gates that have been patched and re-patched for decades. A few blocks over, a 2018 Silicon Beach rebuild may have a brand-new automated sliding gate with a card reader. The Venice Canals neighborhood is its own case: many canal-fronting homes have no vehicle access at all, so the gate is a pedestrian gate mounted feet from open water, with a wooden frame that rots from the bottom up and steel hardware that rusts through in a season or two. The salt-laden sea air pits aluminum castings and corrodes the PCBs inside gate operators far faster than inland. Opener motors that might run 10 to 15 years in the San Fernando Valley often fail within 3 to 5 years in the beach zone if they’re not sealed and maintained. Every quote we write for Venice starts from marine-grade or stainless components, because standard hardware is a short-term fix here.
Our Main Venice Services
Most calls from Venice homeowners land on three things: a gate that has stopped moving, a gate that needs replacing, or a motor that has given up. The common thread is the coastal environment, and each of these services has its own page for the full price breakdown.
Gate Repair in Venice
A gate that drags, sticks, or won’t latch is common in Venice because hinges and rollers corrode quickly in the salt air. On canal-front properties we see wooden pedestrian gates where the bottom rail has rotted out completely while the hardware is still attached to nothing structural. Repair in Venice means diagnosing the specific failure, replacing what failed with marine-grade parts, and documenting the fix. Full pricing and the signs of each failure are on the Gate Repair in Venice page.
Gate Installation in Venice
Venice installations run from single-car driveway swing gates on narrow bungalow lots to pedestrian gates on the Canals where there is no driveway at all. Salt exposure means material selection is the deciding factor: we spec stainless hinges, hot-dip galvanized posts, or composite frames where wood won’t survive. The written quote includes the material grade, not just a style. See the full scope on the Gate Installation in Venice page.
Gate Motor & Opener in Venice
Automated gate opener motors in Venice fail early when condensation and salt get past the housing seal and onto the circuit board. We see it constantly: a motor installed four years ago, dead, with corrosion across the control board terminals. Repair often means a board replacement or a full motor swap, depending on the brand and whether the arm bracket is still intact. Details and prices are on the Gate Motor & Opener in Venice page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Venice
Gate access control in Venice means keypads, remotes, phone entry, card readers, and video intercoms mounted on gates that sit in one of the most corrosive environments in Los Angeles. Salt air gets into every seam, and cheap entry hardware fails within a year or two. We install and service access control with the same marine-grade standard we apply to the gate itself, and every job leaves a photographed record of what was found and what was set. Read the full service overview on our Gate Access Control page.
Keypad Entry
Signs you need it
Buttons stick, the keypad doesn’t respond in damp weather, or the code works intermittently.
What it costs in Venice
New keypad installation in Venice typically runs $280-$550 depending on the keypad brand and whether new wiring is needed.
How we do it
We mount a sealed keypad, run the low-voltage wiring through a weathertight conduit, program the codes, and photograph the finished install.
Video Intercom
Signs you need it
The screen is fogged, the call button doesn’t ring, or the camera image is too clouded to identify a visitor.
What it costs in Venice
Video intercom replacement in Venice runs $450-$1,500, and camera-only fixes usually land under $350.
How we do it
We replace the corroded unit, seal all entry points with marine-grade gaskets, run the wiring, and test the call and unlock functions together.
What Gate Access Control Costs in Venice
| Item | Typical range in Venice |
|---|---|
| Keypad entry installation | $280-$550 |
| Video intercom replacement | $450-$1,500 |
| Phone entry or card reader repair | $180-$475 |
Can you install keypad entry on a canal-front pedestrian gate in Venice?
Yes. We use fully sealed keypads and run the wiring through weathertight conduit, which is what the canal-side moisture requires. A standard gate keypad won’t last there. Call (424) 373-8425 for a written quote.
How long does a gate keypad last near the beach in Venice?
An unsealed keypad near the ocean can fail within 18 months. A weatherproof, marine-rated keypad installed with sealed conduit typically lasts 5 to 7 years in Venice’s salt air. Expect to pay more for the sealed unit, and less in repeat repairs.
Gate Parts & Welding in Venice
Gate parts and welding in Venice is where corrosion shows up first: hinges rust through, steel posts rot at the base, and rollers seize from salt and sand. On the Canals, wooden gate frames rot from the bottom up because they sit inches from open water. We replace parts and perform welding repairs with materials chosen for the beach zone. The full breakdown of what we fix is on the Gate Parts & Welding page.
Hinge Replacement
Signs you need it
The gate sags, the hinge pin is worn thin, or rust has cracked the hinge leaf.
What it costs in Venice
Hinge replacement in Venice runs $120-$350 per hinge, with stainless steel hinges running toward the higher end.
How we do it
We remove the old hinge, bolt on a stainless or hot-dip galvanized replacement, realign the gate, and photograph the new hardware.
Custom Welding
Signs you need it
A cracked weld at the hinge, a broken picket, or a frame that has rusted through at the bottom rail.
What it costs in Venice
On-site welding repairs in Venice run $150-$550 depending on the length of the crack and the access to the gate.
How we do it
We grind out the failed weld, weld the joint with moisture-resistant rod, and coat the repair to match the surrounding finish.
What Gate Parts & Welding Costs in Venice
| Item | Typical range in Venice |
|---|---|
| Hinge replacement (per hinge) | $120-$350 |
| Welding repair | $150-$550 |
| Gate roller replacement | $85-$250 |
Can you weld a rusted-through gate frame in Venice without replacing the whole gate?
Usually yes, if the rot is localized. We weld a steel patch plate over the failed section. If the frame has lost structural integrity across multiple points, replacement is cheaper long-term. Call (424) 373-8425 for an assessment.
Why do gate hinges fail so fast near the Venice Canals?
Canal-front gates sit feet from water, and the constant humidity plus salt accelerates rust. Standard steel hinges fail in one to three seasons. We install stainless hinges on any canal-front job, and the price difference is usually under $100 per hinge.
Brands We Service in Venice
We work on the motor already on your property, and we service more than 470 automated gate operator models from 50 brands, including LiftMaster, Elite, and Mighty Mule. If the part is stocked locally, we can often repair the same visit. See our brands for the full list.
Pricing for Gate Repair in Venice, CA
| Service | Typical range in Venice |
|---|---|
| Keypad entry installation | $280-$550 |
| Video intercom replacement | $450-$1,500 |
| Phone entry or card reader repair | $180-$475 |
| Hinge replacement (per hinge) | $120-$350 |
| Welding repair | $150-$550 |
| Gate roller replacement | $85-$250 |
| Gate motor replacement | $1,500-$3,500 |
| Gate opener circuit board replacement | $250-$550 |
In Venice, the two things that push a price up are salt corrosion on existing hardware and tight access on narrow bungalow lots or canal walkways. Either way, the price is written and handed to you before any work starts, and it doesn’t change at the end of the job.
Neighborhoods We Serve in Venice
We work across all of Venice, from the Canals to the walk streets and the Abbot Kinney corridor. Typical response for a repair call in Venice is same-day or next-day, depending on the failure and the part.
- Venice Canals
- Venice Beach
- Abbot Kinney
- Silver Triangle
- Oakwood
Service Area - Cities Near Venice
For gate work outside Venice, we also serve Culver City, CA, Inglewood, CA, Hawthorne, CA, and Gardena, CA. Each area gets the same written-price standard and documentary photo record.
Serving Venice, CA - Our Local Coverage Area
We’re based in the Venice area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Venice
Most Venice repair calls are handled same-day or next-day. We dispatch technicians to Venice daily, so the response window depends on the failure and whether a specific part needs to be pulled from local stock. Call (424) 373-8425 and a live person answers.
Most like-for-like gate repairs and part replacements don’t require a permit in Los Angeles. New automated gate installations can trigger a permit depending on the scope, particularly on Canal-front or historic properties. We can confirm during the written estimate.
Yes, and we do it often. Canal walkways require carrying tools and materials in from the nearest street access, which we factor into the written price. We also spec stainless hardware and sealed components because the gate sits feet from open water.
If your gate is failing in Venice, call (424) 373-8425. A live person answers 24/7, and every visit includes a written price before any work starts and a photo record of what was found and fixed when we leave.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Venice Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.