Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Los Angeles, CA
Gate access control in Los Angeles is rarely a simple keypad swap. The city’s housing stock spans 1920s Spanish Colonial bungalows with original wrought-iron swing gates to San Fernando Valley tract homes carrying 45-year-old Linear and Stanley operators, and a large share of those properties sit inside LAFD-designated Very High Fire Hazard Severity Zones. That means the work here regularly involves retrofitting older systems for Knox key switches and fail-open logic, not just restoring convenience. Call (424) 373-8425 when you need a technician who understands both the electronics and the fire-zone compliance requirements.
Why Los Angeles Homes Are Different
Coastal neighborhoods like Venice and Marina del Rey punish gate hardware with salt air that corrodes motor housings, hinges, and exposed wiring years faster than inland ZIP codes. Santa Ana wind events in fall and winter derail sliding gates and overtorque swing hinges across the foothills and eastern Valley, producing a predictable seasonal surge in emergency calls. Hillside stucco and brick pilasters shift with soil movement, throwing tracks out of alignment and demanding foundation-level repair alongside the mechanical work. The 2025 Palisades and Eaton fires added another layer: fire-zone neighborhoods like Brentwood, Topanga, and the Hollywood Hills now call specifically for LAFD compliance upgrades, including Knox switches and emergency-override programming on operators that never had provision for them.
Our Main Los Angeles Services
These are the three services Los Angeles homeowners call us about most often, each with its own dedicated page covering scope, pricing, and local conditions in detail.
Gate Repair in Los Angeles
Most repair calls in Los Angeles start as one of three problems: a sliding gate off its track, a swing gate sagging on worn hinges, or an operator that runs but won’t move the gate. Hillside soil movement and Santa Ana wind damage mean we often address both the immediate failure and the underlying alignment issue. We diagnose the mechanical fault, quote a written price, and complete the repair with photographic documentation. Full details live on the Gate Repair in Los Angeles page.
Gate Installation in Los Angeles
Installation in Los Angeles must account for the lot’s terrain, the pilaster condition, and whether the property falls inside a fire hazard zone. We measure, specify the gate and operator, and provide a written scope before any fabrication or site work begins. Stucco and brick pilasters on older homes frequently need reinforcement before a new gate hangs square. The full breakdown is on the Gate Installation in Los Angeles page.
Gate Motor & Opener in Los Angeles
Salt air near the coast and aging Linear-era operators in Valley tract homes make motor replacement one of the most frequent jobs in Los Angeles. We service LiftMaster, FAAC, Elite, and Mighty Mule, among others, and we program fire-zone fail-open logic where LAFD requires it. Written pricing comes before any work starts. See the Gate Motor & Opener in Los Angeles page for full scoping and costs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Los Angeles
Gate access control in Los Angeles means retrofitting older automated gates for keypads, phone entry, card readers, and intercoms, and increasingly it means bringing those systems into LAFD fire-zone compliance with Knox key switches and fail-open programming. Homes built before modern access-control standards, from 1920s bungalows to 1980s Valley tract properties, commonly need new wiring, new readers, and reprogrammed logic. We handle the full Gate Access Control scope, from single-family keypads to multi-tenant phone-entry systems.
Keypad Entry
Signs you need it
The keypad is cracked, unresponsive to some digits, or the gate opens intermittently after a code is entered.
What it costs in Los Angeles
Keypad replacement in Los Angeles runs $200-$550 installed, depending on whether new wiring must be pulled through existing conduit.
How we do it
We remove the old keypad, pull or verify the wiring, mount and program the new unit, and photograph the finished installation.
Phone Entry
Signs you need it
The system won’t dial out, callers can’t hear the dial tone, or the gate won’t release when a resident presses the entry code.
What it costs in Los Angeles
Phone entry systems in Los Angeles range $700-$1,600 installed, including the controller and programming time.
How we do it
We mount the entry controller, connect it to the phone line or cellular module, program the directory, and test access from a live call.
Video Intercom
Signs you need it
The video feed is black, audio is one-way, or the indoor station won’t ring when the exterior button is pressed.
What it costs in Los Angeles
Video intercom installation in Los Angeles runs $900-$2,100, depending on whether the system is Wi-Fi based or requires dedicated wiring.
How we do it
We replace or install the outdoor station and indoor monitor, configure the network or wiring, and verify audio and video in both directions.
What Gate Access Control Costs in Los Angeles
| Item | Typical range in Los Angeles |
|---|---|
| Keypad replacement | $200-$550 |
| Phone entry system | $700-$1,600 |
| Video intercom | $900-$2,100 |
Can you add a Knox key switch to an existing gate in Los Angeles?
Yes. We add Knox key switches to existing operators regularly, especially in fire-zone neighborhoods where LAFD requires emergency access. The key switch mounts outside the gate and ties into the operator’s release circuit. Call (424) 373-8425 for a written quote.
Do access control systems in Los Angeles need to fail open during a power outage?
In designated Very High Fire Hazard Severity Zones, LAFD and LA County Fire often require gates to fail open on power loss so evacuation routes stay clear. We program operators to release on power failure where local code demands it.
Gate Parts & Welding in Los Angeles
Gate parts and welding in Los Angeles means restoring older gates rather than replacing them, which matters on 1920s Spanish Colonial properties with original wrought iron that cannot be matched off the shelf. Salt-air corrosion near the coast eats hinges and rollers, while shifting hillside pilasters crack posts and bend rails. We fabricate and weld on site through our Gate Parts & Welding service, and every job leaves with a photographed record of what was replaced.
Hinge Replacement
Signs you need it
The gate sags visibly, scrapes the ground on the latch side, or the hinge pin has worn through its bushing.
What it costs in Los Angeles
Hinge replacement in Los Angeles runs $80-$280 per hinge, depending on size, material, and whether welding is required.
How we do it
We support the gate, remove the old hinge, weld or bolt the replacement, and verify the gate swings level and square.
Rail Repair
Signs you need it
The gate binds, jumps, or scrapes as it slides, or the rail is visibly bent, rusted through, or pulled away from the pilaster.
What it costs in Los Angeles
Rail repair in Los Angeles runs $180-$470, depending on rail length and whether the mounting pilaster needs concrete work.
How we do it
We straighten or replace the rail section, re-anchor it to the pilaster or footing, and realign the gate trucks and rollers to travel cleanly.
Custom Welding
Signs you need it
A picket is cracked, a frame joint has separated, or the gate has structural damage from wind or vehicle impact.
What it costs in Los Angeles
Custom welding in Los Angeles runs $125-$300 per hour, plus materials, with most repairs completing in one to two hours.
How we do it
We grind the damaged joint clean, weld the repair with the gate in place where possible, and dress the weld to match the surrounding work.
What Gate Parts & Welding Costs in Los Angeles
| Item | Typical range in Los Angeles |
|---|---|
| Hinge replacement per hinge | $80-$280 |
| Rail repair | $180-$470 |
| Custom welding hourly | $125-$300 |
Can you repair a gate that has rusted through in salt air near the coast?
Usually yes. We cut out the rusted section and weld in replacement steel matched to the original profile, then prime and paint the repair. Call (424) 373-8425 for a written quote before work starts.
Do you weld in place or remove the gate?
We weld in place whenever possible. Removing a large swing or sliding gate adds labor and risk of misalignment, so we only remove it when the damage is inaccessible on site.
Brands We Service in Los Angeles
We repair and program LiftMaster, FAAC, Elite, and Mighty Mule operators across Los Angeles, among other major automation brands. Parts for common models are stocked locally for faster turnaround on repairs. See our brands for the full list of what we service.
Pricing for Gate Repair in Los Angeles, CA
| Service | Typical range in Los Angeles |
|---|---|
| Keypad replacement | $200-$550 |
| Phone entry system | $700-$1,600 |
| Video intercom | $900-$2,100 |
| Hinge replacement per hinge | $80-$280 |
| Rail repair | $180-$470 |
| Custom welding hourly | $125-$300 |
Salt-air corrosion near the coast and fire-zone compliance requirements push Los Angeles gate prices toward the upper end of these ranges, since the work often includes additional coating, stainless hardware, or emergency-access programming. Every quote is written and handed over before any work starts, so the price you approve is the price you pay.
Neighborhoods We Serve in Los Angeles
We dispatch local crews across Los Angeles, from the San Fernando Valley to the Westside and into the foothill neighborhoods. Typical response for non-emergency calls is same-week scheduling, with emergency repair prioritized for fire-zone properties where a gate failure blocks evacuation.
- Sherman Oaks
- Silver Lake
- Brentwood
- Hollywood Hills
- Marina del Rey
Service Area - Cities Near Los Angeles
Beyond Los Angeles proper, our crews also serve adjacent cities in the metro area. For gate work in Huntington Park, CA, Gardena, CA, Inglewood, CA, or Downey, CA, the same written-pricing standard and documented photo record applies to every visit.
Serving Los Angeles, CA - Our Local Coverage Area
We’re based in the Los Angeles area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Los Angeles
For fire-zone properties where a failed gate blocks evacuation or emergency access, we prioritize same-day dispatch wherever possible. For non-emergency repairs across Los Angeles, same-week scheduling is typical. A live person answers at (424) 373-8425 around the clock.
Many gate repairs and part replacements need no permit, but new installations, pilaster reconstruction, and some fire-zone compliance upgrades can require city or LAFD review. We identify permit requirements during the estimate and factor them into the written scope.
Yes. Every visit includes a photographed record of what was found, what was adjusted, and what was installed, plus a written record of part numbers and settings. That documentation satisfies most HOA and insurance requests in Los Angeles.
For gate access control, parts and welding, or any other gate repair in Los Angeles, call (424) 373-8425 for a free estimate and a written price before the work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Los Angeles Customers Say
"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.